Projects - Revision history

WikiSysop at 00:01, 23 June 2020

2020-06-23T00:01:53Z

← Older revision		Revision as of 00:01, 23 June 2020
Line 1:		Line 1:
	===[[Planned_Projects\|Planned Projects]]===		===[[Planned_Projects\|Planned Projects]]===
	This is a list of all planned projects for senior project/masters thesis/fun projects/pie-in-the-sky.		This is a list of all planned projects for senior project/masters thesis/fun projects/pie-in-the-sky.

			'''Status: Ongoing'''

			===[[StereoMicroscope\|Stereo Microscope Setup]]===
			Some info on my non-standard stereo microscope setup for electronics work.

	'''Status: Ongoing'''		'''Status: Ongoing'''

WikiSysop at 00:00, 13 August 2019

2019-08-13T00:00:54Z

← Older revision		Revision as of 00:00, 13 August 2019
Line 3:		Line 3:

	'''Status: Ongoing'''		'''Status: Ongoing'''

			===[[Ryobi40V\|Ryobi 40V Charger Reverse Engineering]]===
			Some info on how a Ryobi 40V charger communicates with the battery to enable charging.

			'''Status: Complete'''

	===[[IVSM\|Current/Voltage Sense Module]]===		===[[IVSM\|Current/Voltage Sense Module]]===

WikiSysop at 00:15, 20 March 2019

2019-03-20T00:15:04Z

← Older revision		Revision as of 00:15, 20 March 2019
Line 6:		Line 6:
	===[[IVSM\|Current/Voltage Sense Module]]===		===[[IVSM\|Current/Voltage Sense Module]]===
	This is a 2-channel current + voltage 4-wire sense module for recording low to medium voltage/currents at 16-bit resolution.		This is a 2-channel current + voltage 4-wire sense module for recording low to medium voltage/currents at 16-bit resolution.

			'''Status: Complete'''

			===[[USBSerial\|CH340 Based USB to Serial Adapter Board]]===
			This is a USB to serial adapter board with seperately selectable power and IO voltages, supporting 500mA output current for power (with PTC protection on USB side and power output side), input/output buffered and protected.

	'''Status: Complete'''		'''Status: Complete'''

WikiSysop at 07:37, 17 May 2018

2018-05-17T07:37:44Z

← Older revision		Revision as of 07:37, 17 May 2018
Line 3:		Line 3:

	'''Status: Ongoing'''		'''Status: Ongoing'''

			===[[IVSM\|Current/Voltage Sense Module]]===
			This is a 2-channel current + voltage 4-wire sense module for recording low to medium voltage/currents at 16-bit resolution.

			'''Status: Complete'''

	===[[Solar_Boost\|Solar Battery Charger]]===		===[[Solar_Boost\|Solar Battery Charger]]===

WikiSysop at 01:57, 8 August 2015

2015-08-08T01:57:08Z

← Older revision		Revision as of 01:57, 8 August 2015
Line 106:		Line 106:
	===[[Spectrum Analyzer]]===		===[[Spectrum Analyzer]]===
	This is an overview of the various modules and end result of a homemade 30MHz-2.5GHz spectrum analyzer.		This is an overview of the various modules and end result of a homemade 30MHz-2.5GHz spectrum analyzer.

			'''Status: Ongoing'''

			===[[3D_Printing\|3D Printing]]===
			This is an overview of my adventures in 3D printing.

	'''Status: Ongoing'''		'''Status: Ongoing'''

WikiSysop: Created page with "===Planned Projects=== This is a list of all planned projects for senior project/masters thesis/fun projects/pie-in-the-sky. '''Status: Ongoing''' ===..."

2015-08-07T00:40:07Z

Created page with "===Planned Projects=== This is a list of all planned projects for senior project/masters thesis/fun projects/pie-in-the-sky. '''Status: Ongoing''' ===..."

New page

===[[Planned_Projects|Planned Projects]]===
This is a list of all planned projects for senior project/masters thesis/fun projects/pie-in-the-sky.

'''Status: Ongoing'''

===[[Solar_Boost|Solar Battery Charger]]===
This is a solar charger for supplying power to mobile devices via USB port.

'''Status: Complete'''

===[[Roborodentia_2011|Roborodentia 2011]]===
This is a project to create a fully autonomous robot capable of collecting and scoring ping pong balls into an opponent's net.

'''Status: Complete'''
===[[Quadrifilar_Helix|Quadrifilar Helix]]===
This is a project to create a UHF quadrifilar helix (QFH) antenna for use as an APRS transmit antenna for the [[IEEE_High_Altitude_Balloon_Project|high altitude balloon project]].

'''Status: Complete'''

===[[Rev0Trac|rev0Trac]]===
This is a project to create an APRS tracking beacon to transmit GPS coordinates and other data via radio.

'''Status: In Progress'''

===[[Rev0Trac_UTx|rev0Trac UTx]]===
This is a project to create an APRS all-in-one UHF transceiver, building on the capability of the [[Rev0Trac_VTx|rev0Trac VTx]].

'''Status: In Progress'''

===[[Misc_Projects|Breakout Boards and Misc. Projects]]===
This is a list of small projects such as breakout boards for various chips that have been made.

'''Status: Ongoing'''
===[[EE_306_Sustainability_Analysis|EE 306 Sustainability Analysis]]===
This is the sustainability analysis project for EE 306 -- Semiconductor Device Electronics, for Fall 2010.

'''Status: Complete'''

===[[EE460_Reverse_Engineering|EE 460 Reverse Engineering]]===
This is the reverse engineering team project for EE 460 -- Senior Project Preparation, for Fall 2011.

'''Status: Complete'''
===[[Puxing_PX-2R|Puxing PX-2R Teardown]]===
This is a full teardown and disassembly of the Puxing PX-2R 70cm Handheld Transceiver, including pictures of the main PCB and parts list.

'''Status: In Progress'''

===[[Dorji_DRA808M|Dorji DRA808M Teardown]]===
This is a teardown and analysis of the Dorji DRA808M 1W 400-470 MHz FM radio module.

'''Status: In Progress'''

===[[IEEE_High_Altitude_Balloon_Project|IEEE Student Branch - High Altitude Balloon Project]]===
This is a project to send a helium weather balloon into near-space (80,000-100,000 feet) and report back various sensor measurements, including pressure, temperature, GPS coordinates, altitude, and others, in real time.

'''Status: In Progress'''
===[[IEEE_Laser_Projector|IEEE Student Branch - Laser Projector Project]]===
This is a project to build a monochrome, 640x480, 30 fps laser projector that will interface with a computer and display images and video in real time.

'''Status: In Progress'''
===[[LaserScan]]===
This is a project to build a 24-bit color laser projector that can interface to a computer to display video or pictures in real time.

'''Status: On hold until green diode source is obtained'''
===[[Versadrive]]===
This is a 1 amp, 3 mode constant current laser boost driver, featuring a user-selectable software interlock and battery indicator.

'''Status: Abandoned'''
===[[445nm_1W|445nm 1W Laser]]===
This is a 1 watt 445nm laser in a stainless steel 18650 host.

'''Status: Complete'''
===[[GC-D_100|GC-D 100]]===
This is a project to build a fully functional digital Geiger counter.

'''Status: Complete'''
===[http://robotics.ee.calpoly.edu/old/doku.php?id=2010_internal_competition:team4:start Consilium]===
This is a bot for the Cal Poly Robotics Club inter-club competition for 2010.

'''Status: Complete'''

===[[Laser_Drivers|Laser Drivers]]===
This is a list of several common laser driver types.

'''Status: Under Construction'''
===[[Lasers]]===
This is a list of all lasers currently owned or being created.

'''Status: Ongoing'''

===[[FPV]]===
This is a description of my FPV tricopter and associated equipment.

'''Status: Ongoing'''

===[[CNC]]===
This is an overview of my experience and capabilities with CNC milling.

'''Status: Ongoing'''

===[[Xray]]===
This is an overview of my adventure in Xray photography.

'''Status: Ongoing'''

===[[Spectrum Analyzer]]===
This is an overview of the various modules and end result of a homemade 30MHz-2.5GHz spectrum analyzer.

'''Status: Ongoing'''