Skip to content
Rev0 Wiki archive

SCARA

Last edited

Contents
  1. Summary
  2. Subsystems
  3. Z-Axis Drive
  4. X/Y-Axis Drives
  5. Bill of Materials

Summary

The design of this robot is based heavily on the "HF06" robot designed by Martin Price (link). It was initially undertaken as a low-cost 3D positioning robot for use in touch-screen testing or button pressing/activation, but evolved into a 3D printer (with replacable tool head, so still capable of performing basic 3D positioner tasks). The X/Y resolution is lower than typical 3D printers, but is estimated to still be adequate (resolution is <1/4 the diameter of the extruded filament diameter).

Subsystems

Z-Axis Drive

The Z axis is driven by a 1.8 degree per step NEMA-23 motor, purchased at All Electronics (link). It uses an 8-wire interface, with 2 sets of coils wired in parallel or series for each phase). Wiring info is below:

  • black to red = 3.4 ohms
  • brown to blue = 3.5 ohms
  • orange to green = 3.5 ohms
  • yellow to white = 3.5 ohms


  • black: 0 ohms to 1, 3.5 ohms to 3
  • red: 0 ohms to 3, 3.5 ohms to 1
  • brown: 0 ohms to 7, 3.5 ohms to 5
  • blue: 0 ohms to 5, 3.5 ohms to 7
  • white: 0 ohms to 4, 3.5 ohms to 2
  • yellow: 0 ohms to 2, 3.5 ohms to 4
  • orange: 0 ohms to 6, 3.5 ohms to 8
  • green: 0 ohms to 8, 3.5 ohms to 6


The motor is coupled to a 1/4"-20 shaft which drives the SCARA X/Y positioner via an anti-backlash assembly comprised of two 1/4"-20 bolts held apart by a spring. The Z-axis assembly has 1.27 revolutions per mm, and using an 8-microstep controller gives 0.79375 um/step (1259.843 steps/mm), or 6.35 um/step (157.480 steps/mm) in full-step mode. The Z-axis print resolution will ultimately depend on machine tolerances and bed leveling, as it is clearly not limited by motor/mechanical resolution.

X/Y-Axis Drives

The X/Y axis are covered by the SCARA, and are driven by two 1.8 degree per step NEMA-17 motors, also purchased at All Electronics (link). Each motor is coupled to the 165mm arms via a 5:1 reduction pulley using GT2 2mm belts. Each motor will be driven by a 1/32 microstepping driver (DRV8825) for a total resolution of 0.01125 degrees/step, giving a worst-case linear step of 100um in X/Y (approximately 1/10th the resolution of a typical Cartesian bot, 1/10-1/3 that of a typical Delta, or about 1/2 to equal that of a DLP SLS printer).

Bill of Materials

PartQuantityUnit CostTotal CostSource
NEMA-17 1.8 deg. Motor2$6.50$13.00All Electronics
NEMA-23 1.8 deg. Motor1$8.50$8.50All Electronics
Shipping (All Electronics)1$7.00$7.00All Electronics
MotorsTotal Cost$28.50
1/4"-20 Threaded Rod 12"1$0.96$0.96Home Depot
608ZZ Bearing4$0.305$1.22eBay
8mm x 300mm Linear Rail2$6.69$13.38eBay
LM8UU Linear Bearing4$0.599$2.40eBay
MechanicalsTotal Cost$17.96
12V 100W Power Supply1$11.94$11.94eBay
Stepper Driver (DRV8825)4$2.26$9.04eBay
Arduino Mega1$11.50$11.50eBay
RAMPS Board1$6.49$6.49eBay
Control ElectronicsTotal Cost$38.97
NEMA-17 1.8 deg. Hi-Torque Motor1$12.00$12.00eBay
MR105ZZ Bearing1$0.256$0.26eBay
Airtripper Metal Parts Kit1$12.79$12.79eBay
MK8 Drive Gear1$8.99$8.99eBay
E3D-v6 Bowden Extruder1$83.25$83.25E3D
ExtruderTotal Cost$117.29
Total Unit Cost$202.72